西安电子科技大学学报 ›› 2021, Vol. 48 ›› Issue (4): 42-49.doi: 10.19665/j.issn1001-2400.2021.04.006

• 信息与通信工程&电子科学与技术 • 上一篇    下一篇

同轴电缆感性脉冲电流注入试验仿真方法

崔志同1(),魏兵2(),吴伟1(),孙蓓云1()   

  1. 1.西北核技术研究所 强脉冲辐射模拟与效应国家重点实验室,陕西 西安 710024
    2.西安电子科技大学 物理与光电工程学院,陕西 西安 710071
  • 收稿日期:2020-06-22 出版日期:2021-08-30 发布日期:2021-08-31
  • 作者简介:崔志同(1981—),男,高级工程师,博士,E-mail: zhitong_cui@163.com|魏 兵(1970—),男,教授,博士,E-mail: bwei@xidian.edu.cn|吴 伟(1976—),男,高级工程师,博士,E-mail: wuwei@nint.ac.cn|孙蓓云(1967—),女,高级工程师,博士,E-mail: sunbeiyun@nint.ac.cn
  • 基金资助:
    国家自然科学基金(61901324);国家自然科学基金(62001345);强脉冲辐射环境模拟与效应国家重点实验室基金(SKLIPR1705);强脉冲辐射环境模拟与效应国家重点实验室基金(SKLIPR1901)

Simulation methods for inductive pulsed current injection on the coaxial cable

CUI Zhitong1(),WEI Bing2(),WU Wei1(),SUN Beiyun1()   

  1. 1. State Key Laboratory of Intense Pulsed Radiation Simulation and Effect, Northwest Institute of Nuclear Technology,Xi’an 710024,China
    2. School of Physics and Optoelectronic Engineering,Xidian University,Xi’an 710071,China
  • Received:2020-06-22 Online:2021-08-30 Published:2021-08-31

摘要:

为开展同轴电缆感性脉冲电流注入试验的量化分析及设计,利用Spice建模的方法求解电缆屏蔽层的耦合电流,给出了脉冲电流注入仿真中转移阻抗适用的测试方法以及屏蔽层与芯线间耦合的计算方程,建立了同轴电缆感性脉冲电流注入的Spice+Matlab联合仿真方法;另外,基于响应等效原理解决了负值电感的Spice电路表征问题,建立了转移阻抗实测值的拟合电路模型,继而在完成屏蔽层与芯线间耦合的集总近似电路建模的基础上,实现了同轴电缆感性脉冲电流注入的全Spice电路仿真。经数值和实验验证,上述两种方法一致性较好,且均具有较高的仿真精度和良好的时域收敛性,可以用于同轴电缆感性脉冲电流注入试验的设计、分析、效果预估等工作。

关键词: 强瞬态电磁干扰, 传导试验方法, 脉冲电流注入, 转移阻抗, Spice电路仿真

Abstract:

This paper aims at a quantitative analysis and the design of the inductive PCI (Pulsed Current Injection)on coaxial cables.First the induced current on the cable shield is derived by Spice circuit modeling.And the reasonable measurement method and coupling equations between the shield and inner conductor are proposed under the specific boundary conditions decided by the PCI.Then a Spice+Matlab simulation method for the inductive PCI on coaxial cables is developed.Furthermore,the negative inductor and the fitting circuit model of transfer impedance are expressed in Spice based on the principle of circuit equivalent response.Then the lumped approximate model of the coupling circuit between the shield and inner conductor is developed by subdividing the cable into several electrical small subsections.Finally a complete Spice model for the PCI on coaxial cables is constructed.By numerical and experimental validation,the two aforesaid methods have an appreciable agreement and show a high simulation precision and convergence in the time domain.Both of them will be very helpful to analysis and design of the PCI on coaxial cables.

Key words: intense transient electromagnetic pulse, conducted test method, pulsed current injection, transfer impedance, Spice modeling

中图分类号: 

  • TM13